Woolaston Vero/Stripboard Schematics

Started by WhiteWarlock, April 06, 2018, 07:12:22 PM

Previous topic - Next topic

WhiteWarlock

nicolas3141

Joined: May 25, 2007
Posts: 185
Location: Christchurch, New Zealand



Veroboard is great and not difficult to use. If you must have the most compact design it can be frustrating, but if you are happy to use just a little more space it makes things a lot more enjoyable. Same with PCB design I guess. Anyway, my recipe for easy veroboard layout goes like this:

1. Start with a piece of veroboard about 80mm square. It usually doesn't need to be quite as big as that, but the extra gives you some room for later kludges if necessary. Or for a simple circuit 50mm square is plenty.

2. Align all the chips in a row (line astern) with about 3 stripes in between each one. Most veroboard comes in widths of about 80mm, so this technique works best for circuits with no more than three 14/16 pin chips or five 8 pin chips.

3. Use a mini grinder or similar tool to cut all the tracks from one side to the other underneath the line of chips. Its _much_ easier to cut all the tracks in one line rather than fuss about cutting some here and some there.

4. Run resistors, caps and wire links parallel to the line of chips wherever possible.

5. Designate one stripe between each chip as a ground and use a wire link to bridge the cut you just made.

6. If you need to cross the line of chips with a wire or resistor, I recommend doing it on the copper side of the board, so all my vertical oriented components are on one side and laterals on the other. I also recommend attaching front panel wires on the copper side (surface mount fashion) rather than through the holes.

Doing it this way you can often get away with building direct from a schematic rather than having to go through a separate board design process.

Cheers,
Nicolas












Woolaston ADSR PCB LAYOUT















tri2saw


vca-simpler



Touch sensitive noise - cracklebox derivative





Simple ribbon controller for V/Hz synth:
http://electro-music.com/forum/topic-32651.html

Super simple V/Hz VCO:
http://electro-music.com/forum/topic-32689.html

Pitch-not-critical Sooper-Simple VCO;
http://www.electro-music.com/forum/topic-38087.html

Simple sawtooth VCO
http://electro-music.com/forum/post-292718.html

V/Hz state variable filter:
http://electro-music.com/forum/topic-34426.html

Noise source:
http://electro-music.com/forum/topic-34745.html

TRI2SAW:
http://electro-music.com/forum/topic-27934.html

ADSR:
http://electro-music.com/forum/topic-31473.html

LFO & VCLFO:
http://electro-music.com/forum/topic-32372.html

Simple S&H and VCA
http://electro-music.com/forum/topic-41277.html


updated and edited, 08-05-10, by v-un-v







some super simple Woolaston vero/strip boards for Special Interests from the archives
hertz VCOs
works with Korg ms20,ms10,ms50,x911,old yamaha cs, & vintage PAIA plus FATMAN
good examples for basic vero/stripboard DIY method
Is it better to out-monster the monster or to be quietly devoured?
FreakMaker
SynthWizards/N01ZE

Euro Trash Bazooka

I'd be very interested (although I swore I'd never use veroboard for anything but very simple circuits like fuzz pedals anymore) but pleaaaase use Fritzing to make your schematics. I can't read anything on your designs...

Thank you for sharing all this stuff though.
DROIT DIVIN: https://droitdivin1.bandcamp.com/

CRYPTOFASCISME / VIOLENT SHOGUN /
ETC: https://yesdivulgation.bandcamp.com/

WhiteWarlock

we have that fisher price tape recorder.... GF had to have it... those are Nicolas Woolastons' vero designs... we have built many of them
Thumbs up for Fritzing
yet personally have habit defaulting to the old DIY stripboard maker
Is it better to out-monster the monster or to be quietly devoured?
FreakMaker
SynthWizards/N01ZE